Handwork: bags, cases, pencil cases and cases for IT

Send

Not so much is needed to become the owner of a designer thing: genuine leather, lining fabric, a little accessories and patience.

BIG BAG
It will fit all the most precious - Book Reader, IPhone, iPad and something else.
Size approx. 38 x 35 cm

YOU WILL NEED Genuine nappa leather - 2 plates, size 45 x 60 cm; lining fabric 50 x 65 cm; 4 blocks of color of gold to internal dia. 1.5 cm; 2 rings for the handle of color of gold to dia. 5 cm; a carbine with a ring and a half ring 2 cm wide; 4 rivets diam. 8 mm each; textile glue, threads for sewing.
CUT
Leather:
■ 2 main parts of the bag 42 cm long, of which 5 cm are all-cut top hemming and 50 cm wide, including allowances
■ belt loader 30 cm long, handle 60 cm long and 3 cm wide, including allowances
From lining fabric:
■ 2 main parts of a bag 34 cm long and 50 cm wide, including allowances
SEWING
Parts of leather bags to grind. Start the lining details, in the lower seam leave an open area of approx. 15 cm for eversion. Iron allowances.
Pull the lining on the bag face to face, grind the upper sections to a width of 1 cm. Unscrew the bag. Unscrew the top trim from the inside, iron the top edge of the bag.Sew the open area in the seam of the lining.
At a distance of 3 cm below the top edge of the bag, on both sides of the side seams at a distance of 7.5 cm, put tags for the blocks. Cut holes diam. 1.5 cm = inner diameter. blocks, set blocks. Insert a ring on each side into both side blocks.
Unscrew the longitudinal sections of the handle and belt loops 7 mm wide and glue them on the wrong side. Stitch edges to edge. Insert the handle into the ring with the inside inward and fold it almost in half, but leave the top end of the handle 3 cm protruding. Punch the rivet 3 cm above the ring. Insert the upper protruding end of the handle into the carabiner ring, place it on the other end of the handle and fasten with a rivet.
Pass the loops in the ring and fold them almost in half, but leave one end protruding 3 cm. Punch the rivet at a distance of 3 cm from the half-ring. Pass the long end of the belt loop through a large ring, put on the second end of the belt loop and fasten with a rivet. Fasten the carabiner to the half ring.AND SO YOU CAN SEW A BIG BAG WITH CORNERS FORMING THE BOTTOM

YOU WILL NEED Leather (2x. 42 x 50 cm, 30 x 3 cm, 60 x 3 cm); lining fabric (size 34 x 50 cm); 4 blocks; 2 rings (diam. 5 cm); 1 half ring; 1 carbine with a ring diam. 2 cm; 4 blocks.
STEP 1 Fold the leather and lining parts face to face, chop off two short and one long sides, and grind them to a width of 1 cm.
STEP 2 Ironing allowances.

STEP 3 Fold the bottom corners of the bag so that the side seam aligns with the bottom seam. Mark the transverse seam 4 cm from the corner. Stab angle.
STEP 4 Start the transverse seam along the marking.
STEP 5 Wrap the corners towards the bottom of the bag and sew a few stitches by hand to the allowances. Next, sew according to the description above for a large bag.

LEATHER CASE WITH LIGHTNING
Just a godsend for a mobile phone.
Size 18 x 8 cm
YOU WILL NEED Plate genuine leather nappa size. 25 x 30 cm, textile glue; threads for sewing.
CUT TO:
■ 2 rear parts, one-piece with a valve, 26 cm long, 8 cm wide, including allowances
■ front part 16 cm long, 8 cm wide, including allowances
■ tie with a total length of 60 cm and a width of 5 mm, including allowances
SEWING
The rear parts, one-piece with a valve, glue inside out to the wrong side. Round all corners. Put the front part on the back inside out on the face, fasten the sections with paper clips, leave the valve protruding. Stitch the back to the edge, adjusting the front. Slices of the front part to equalize the slices of the rear part.
Unscrew the valve down by 8 cm. Stitch the parts of the tie into one long tie. Wrap the tie around the handbag and tie a bow in front.
Stitch the tie on the sides 3 cm above the lower edge of the valve, laying a line over the existing one and not grabbing the valve.

CASING MOBILE CASE
It can also be used for various little things (however, like a case with a zipper), for example, for cosmetics.
SIZE OK. 21 x 6 cm
YOU WILL NEED Plate genuine leather nappa size. 25 x 20 cm; 1 metal zipper 18 cm long; threads for sewing.
CUT
■ lower part 22 cm long and 7 cm wide, including allowances
■ 2 tops 22 cm long and 5 cm wide, including allowances.
SEWING
Fold upper parts face to face. Make an average seam 1.5 cm long at both ends at a distance of 1.5 cm (width of the allowances).
Iron seam allowances, iron allowances along the edges of the cut between the seams. Place the zipper under the edges of the cut so that the teeth are not visible. Stitch the allowances along the edges of the cut to the braid of lightning to the edge. Open the zipper, fold the lower and upper parts face to face and grind the perimeter sections to a width of 5 mm.
To turn out a handbag.
The material was prepared by Elena Karpova.
Photo: Hans Buttermilch (2); Jan Schmiedel; idea and embodiment: Rushana Jennings.

Send